DLE20 20CC GAS ENGINE

specification:

This is the DLE 20cc Gasoline Powered Engine with Electronic Ignition

FEATURES: Two sealed bearings on crankshaft-simple design for lighter weight
Beam mounting allows easy fit in the same mount as comparable glow
engines
Aluminum alloy crankcase with advanced CNC machining
Rear mounted pumper carburetor ensures easier installation and smooth
idling and dependable fuel flow during flights
Fully automatic electronic ignition
Two year limited warranty through Hobby Services beginning at date
of purchase

INCLUDES: Engine, spark plug, four standoffs, ignition, muffler, muffler
gasket, two 5x20mm muffler bolts, four 5x60mm mounting bolts
instruction manual

REQUIRES: Gasoline with at least 87 octane rating
2-cycle oil, mix ratio for this engine is 30 parts gas to one part
oil and must be followed exactly for warranty consideration
and optimum performance
4.8 - 6V NiMH/NiCd, or 6.6V LiFe or 7.4V LiPo battery for ignition
(separate receiver style pack can be used) (LiPo use requires
voltage regulator)
Propeller and field equipment

SPECS: Output Power: 2.5 HP at 9,000 RPM
Idle Speed: 1,750 RPM
Static Thrust: 6 kg Pulling Force/100 meters altitude
5.3 kg Pulling Force/1,800 meters altitude
Displacement: 1.22cu in (20cc)
Bore and Stroke: 1.3 x 1.0" (32 x 25mm)
Compression Ratio: 10.5:1
Weight: Engine: 22.93oz.(650g)
Exhaust: 1.76oz (50g)
Ignition: 4.23oz (120g)
Total: 28.9oz (820g)
Gasoline/Oil Mixture: 30:1
Gasoline Octane Rating: 87-93
Recommended Propellers: 14x10, 15x8, 16x6, 16x8, 17.6, 18x6
(break-in prop not specified)
Ignition Battery: 4.8 - 6V, BEC required if LiPo battery is used
Spark Plug: CM6
Spark Plug Gap: 0.018 - 0.020"
Plug Installation Torque: 7 - 8ft-lbs
Carburetor Adjustments;
Low Speed Needle: 1.5 turns out as a starting point, adjust for a
smooth idle and a reliable transition to high throttle
High Speed Needle: 1.5-2 turns out from closed, adjust needle to peak
RPM, if engine slows or dies at full throttle, the high-speed
mixture is likely too lean
Height from bottom/Crankcase to top of Cylinder Head: 5.4" (138mm)
Height/bottom/of Mounting Tab to top of Cylinder Head: 3.4" (87.5mm)
Width of Cylinder Head: 2.5" (65mm)
Width at Mounting Tabs: 2.8" (70.5mm)
Distance/Mounting Hole Centers Same Side: 1.0" (26mm)
Distance/Mounting Hole Centers Opposite Side: 2.4" (60mm)
Height of Exhaust Opening: 0.42" (10.8mm)
Width of Exhaust Opening: 0.83" (21mm)
Length from Carburetor to Front Bearing: 4.5" (114mm)
Length from Carburetor to Prop Hub: 5.1" (130mm)
Total Height of Muffler including Exhaust Pipe: 3.8" (96mm)
Center of Muffler Exhaust Opening to end of Pipe: 2.4" (61mm)
Muffler Width: 2" (52.1mm)
Exhaust Pipe Inner Diameter: 0.56" (14.2mm)
Crankshaft thread size: 5/16-24

COMMENTS: To avoid permanent damage to the electronic ignition system, NEVER
turn your DLE engine over with the system switched on and the plug
not installed.


DL POWER

Part DLE-20

General Item Information
All items are brand new in the original package unless specifically stated in the listing.
The image shown is for reference only.
The image may depict the item with other accessories or in a completed state to give a better depiction of the items use and/or qualities.
Please refer to the description for what is included in this listing.