Multi Frequency Rolling Code Duplicator Remote Control Liftmaster 280-868MHz

WE HAVE AVAILABLE BLACK/RED/BLUE, send us a message with your specifications (If no message we will provide black color by default)

Features:
Duplicating procedures:



Check below list at the bottom for detailed compatibility (BFT, Beninca, Liftmaster, Chamberlain, Sears Craftsman, Lockmaster, Viking, Powermaster, Haudini, Viper, Cylcone, NSEE, Linear, Multicode, GTO, Mighty Mule and many more)

Compatible with overhead operators and garage doors



Manual included




Part 1:Fixed code duplicating procedures
1. Press & hold button 1 of the duplicator, meanwhile press 4 times the 2 button.

2. Release both buttons. Now the RED LED emits a short flash every 2 seconds.

3. Place the original remote control next to duplicator around 5cm

4. Keep pressing the button of the original remote control and wait for a change flash (as a faster flash) of duplicator RED LED and a change of its color (BLUE) that confirms the correct learning of code. This step may take a few seconds and during that the color LED is WHITE.

5. While the BLUE LED is flashing, press the button of the duplicator where you want to program the code just learnt, and retain pressed until the LED switches off and an extended sound “BEEP” for a reconfirmation of the correct code learning.

This step may take some seconds.

6. The copy has been happened with success. Repeat the duplication from step 1 to the rest buttons.



Part 2:Rolling code (Simple code) duplicating procedures
1. Press & hold button 1 of the duplicator, meanwhile press 4 times the 2 button.

2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.

3. Place the original remote control next to duplicator around 5cm

4. Keep pressing the button of the original remote control and wait for a change flash (as a faster flash) of duplicator RED LED and a change of its color (BLUE) that confirms the correct learning of code. This step may take a few seconds and during that the color LED is WHITE.

5. While the BLUE LED is flashing, press the button of the “duplicator” where you want to program the code just learnt, and retain pressed until the LED will switch off. The duplicator remote control will emit an extended sound “BEEP” for are confirmation of the correct code learning.

6. Repeat the duplication from step 1 to the rest buttons.

7. Activate now the correct procedure for the programmed model and insert the new remote control on the receiver (seethe compatibility list present in this manual).

Part 3:Rolling code (Complex code) duplicating procedures

3.1 BFT



1. Press & hold button 1 of the duplicator,meanwhile press 4 times the 2 button.

2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.

3. Place the original remote control next to duplicator around 5cm

4. Keep pressing the button to be programmed of the original remote control, till the RED LED will switch on as a fix light; now release the button.

5. The duplicator RED LED will emit a short flash every 2 seconds supported by two following sound “BEEP”. These two alerts indicates it is necessary to emit the SEED CODE to realize the copy.

6. To transmit the SEED CODE of the BFT original remote control, please using a pin, press the rear hide button (see the picture)or, according to the new references, press the 1 and 2 buttons until the original remote control LED switches on.
7. Now the duplicator RED LED will change the flash mode (more fast) and color (BLUE), for a reconfirmation of the correct code learning. This step may take some seconds.


8. At this moment, press the duplicator button when you want to store the code and retain pressed until the duplicator BLUE LED switches off and an extended sound “BEEP” is emitted for a reconfirmation of the correct code learning. Repeat the duplicationg from Step 1 to the rest buttons.

9. Activate now the DOR procedure to insert the new remote control on the receiver.





1. Press & hold button 1 of the duplicator,meanwhile press 4 times the 2 button.

2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.

3. Place the original remote control next to duplicator around 5cm

4. Keep pressing the button to be programmed of the original remote control, till the RED LED will switch on as a fix light; now release the button.

5. The duplicator RED LED will emit a short flash every 2 seconds supported by two following sound “BEEP”. These two alerts indicates it is necessary to emit the SEED CODE to realize the copy.

6. To transmit the SEED CODE of the V2 original remote control, please press at the same time 1 and 2 buttons.

7. Now the duplicator RED LED will change the flash mode (more fast) and color (BLUE), for a reconfirmation of the correct code learning. This step may take some seconds.

8. At this moment, press the duplicator button when you want to store the code and retain pressed until the duplicator BLUE LED switches off and an extended sound “BEEP” is emitted for a reconfirmation of the correct code learning. Repeat the duplicationg from Step 1 to the rest buttons.

9. Activate now DOR the procedure to insert the new remote control on the receiver.



3.3:FAAC 433 - 868


Attention: verify the programming remote control is a MASTER. Pressing whatever button, the LED has to emit a double flash rather than to switch on as a fixed light.

1. Press & hold button 1 of the duplicator,meanwhile press 4 times the 2 button.

2. Release both buttons. Now the duplicator RED LED will emit a short flash every 2 seconds.

3. Place the original remote control next to duplicator around 5cm




4. Keep pressing the button to be programmed of the original remote control, till the RED LED will switch onas a fix light; now release the button.

5. The duplicator RED LED will emit a short flash every 2 seconds supported by two following sound “BEEP”. These twoalerts indicates it is necessary to emit the SEED CODE to realize the copy

6. Predispose the FAAC/GENIUS remote control for the SEED CODE emission. Press at the same time the 1 and 2 buttons(note: THESE ARE THE BUTTONS OF THE DIAGONAL LINE).


7. While FAAC/GENIUS remote control LED flashes, place it in front of duplicator at a distance of 5cm and press thebutton to be programmed until the duplicator RED LED will change the flash mode (more fast) and color (BLUE), for areconfirmation of the correct code learning. This step may take some seconds..

8. At this moment, press the button when you want to store the code and retain pressed until the duplicator BLUE LED,switches off and an extended sound “BEEP” is emitted to confirm the correct learning of the code. Repeat the duplicationg from Step 1 to the rest buttons.



9. The copy has been happened with success. Now check on the automation the correct functioning of new duplicatorremote control pressing two times the copied button.


Part 4:Source duplicator to new duplicator duplicating procedures

1. Press & hold button 1 of the NEW duplicator,meanwhile press 4 times the 2 button.

2. Release both buttons. Now the RED LED of “NEW duplicator” will emit a short flash every 2 seconds.

Place the “SOURCE duplicator” in front of the “NEW duplicator

around 5cm

4. Keep pressing the button to be programmed of the “SOURCE duplicator”