$52.00
Add to Cart
MICRO-3 Traffic Light Signal Controller Sequencer ( 3 output )
Only 1 available, 218 sold
Details
Shipping: US-Mainland: $11.50 (more destinations)
Condition: Brand new
Shipping restrictions:
Please note this item only ships within the USA.
We do not ship outside the USA.
Three Output Traffic Controller / Sequencer
Model# MICRO-3 (in Plastic PCB carrier)
Standard Sequence:
GREEN
YELLOW
RED
(repeat)
If you have a 3-light traffic signal hanging in your game room, basement, garage, etc. and would like to make it operate like a REAL stop light, you are in the right place. Measuring only 2-1/8" X 1-7/8" (Plastic Carrier Dimensions), this board fits easily into a standard traffic signal.
Features:
Fully Independent light-times:
Yellow duration is not tied to red/green duration
Red and Green timing does not have to be the same
Extended cycle timing range from 1/2 second to over 20 MINUTES per light
Ultra Compact Size (Approx. 2" X 2")
Screw-Terminal connections, eliminating the need for soldering
100 Watts per output channel
LED compatible (120 vac)
Simple TIME-SETTING procedure
Wiring Diagram is Included (download PDF )
User-replaceable fuse (Type GMA 2 - 2.5A)
All solid-state on-board switching electronics
120 VAC 60HZ standard voltage operation
Retains timing even if power is removed
OVERVIEW
Each lights timing can be set differently, with a possible range of 1/4 second to 20 minutes PER LIGHT. Yellow-Light timing is not tied to the RED / GREEN times.
The fuse is user replaceable. Fuse type is GMA 2A - 2.5A 125/250VAC available from any local Home Depot or Electronic store.
MOUNTING:
The plastic carrier can be adhered to any flat, non-porous surface with double sided sticky tape.
Every unit is fully tested before shipment. A wiring diagram is included with circuit board.
instructions PDF link:
http://www.joezgarage.com/Micro-3-inst.pdf
WARNING: Basic electrical wiring skills for this item are required.
Familiarity with 120 VAC / High Voltages is also required.
Improper wiring of this unit can result in an electrical shock.
Controller / Sequencer Specifications
Range (Min - Max)
Operating Voltage: 108 - 120 VAC
Output Channels:
3 signal: green, yellow, red
Total Wattage per output channel: 100 watts @ 120VAC
Green Light Timing Range: From 1/2 second to 20 MINUTES
Yellow Light Timing Range: From 1/2 second to 20 MINUTES
Red Light Timing Range: From 1/2 second to 20 MINUTES
Setting timing overview...
Using a plastic pen or similar non-conductive item, press and hold down TIME-SET button for 5 seconds until TIME-SET-LED comes on, then release button.
Press and release the TIME-SET button when you want the signal to advance to the next light. Do this for each light.
Once the red-light timing is set, the TIME-SET-LED will turn off and the controller will start normal operation.
note: The new time settings will remain in memory EVEN IF POWER IS REMOVED.
Please note this item only ships within the USA.
We do not ship outside the USA.
Three Output Traffic Controller / Sequencer
Model# MICRO-3 (in Plastic PCB carrier)
Standard Sequence:
GREEN
YELLOW
RED
(repeat)
If you have a 3-light traffic signal hanging in your game room, basement, garage, etc. and would like to make it operate like a REAL stop light, you are in the right place. Measuring only 2-1/8" X 1-7/8" (Plastic Carrier Dimensions), this board fits easily into a standard traffic signal.
Features:
Fully Independent light-times:
Yellow duration is not tied to red/green duration
Red and Green timing does not have to be the same
Extended cycle timing range from 1/2 second to over 20 MINUTES per light
Ultra Compact Size (Approx. 2" X 2")
Screw-Terminal connections, eliminating the need for soldering
100 Watts per output channel
LED compatible (120 vac)
Simple TIME-SETTING procedure
Wiring Diagram is Included (download PDF )
User-replaceable fuse (Type GMA 2 - 2.5A)
All solid-state on-board switching electronics
120 VAC 60HZ standard voltage operation
Retains timing even if power is removed
OVERVIEW
Each lights timing can be set differently, with a possible range of 1/4 second to 20 minutes PER LIGHT. Yellow-Light timing is not tied to the RED / GREEN times.
The fuse is user replaceable. Fuse type is GMA 2A - 2.5A 125/250VAC available from any local Home Depot or Electronic store.
MOUNTING:
The plastic carrier can be adhered to any flat, non-porous surface with double sided sticky tape.
Every unit is fully tested before shipment. A wiring diagram is included with circuit board.
instructions PDF link:
http://www.joezgarage.com/Micro-3-inst.pdf
WARNING: Basic electrical wiring skills for this item are required.
Familiarity with 120 VAC / High Voltages is also required.
Improper wiring of this unit can result in an electrical shock.
Controller / Sequencer Specifications
Range (Min - Max)
Operating Voltage: 108 - 120 VAC
Output Channels:
3 signal: green, yellow, red
Total Wattage per output channel: 100 watts @ 120VAC
Green Light Timing Range: From 1/2 second to 20 MINUTES
Yellow Light Timing Range: From 1/2 second to 20 MINUTES
Red Light Timing Range: From 1/2 second to 20 MINUTES
Setting timing overview...
Using a plastic pen or similar non-conductive item, press and hold down TIME-SET button for 5 seconds until TIME-SET-LED comes on, then release button.
Press and release the TIME-SET button when you want the signal to advance to the next light. Do this for each light.
Once the red-light timing is set, the TIME-SET-LED will turn off and the controller will start normal operation.
note: The new time settings will remain in memory EVEN IF POWER IS REMOVED.
















