($9,407) Wood Chipper 824PTO - 4" CAPACITY MINIMUM 15 HP REQUIRED AT THE PTO.
4" x 8" , Hydraulic Feed (Self Contained Hydraulics)
($1,176) Speed Sensing.
($2,694) Skid Steer Adapter Plate 824PTO, (Specify Standard Flow or High Flow)
YouTube Video: https://youtu.be/odnAAOhZyr8
Made in the USA.
The Model 824 is no ordinary 4" Chipper. This is a very compact unit, but not a light-weight. Very well constructed with all continuous welds and a tubular steel frame. This unit is fully contained and requires no oil from the tractor. The 824 easily connects to any Category 1, 3-Point Hitch tractor. The 360 degree exhaust is easily adjusted to discharge chips anywhere you want. This unit will work from dawn to dusk for many years to come.
Speed Sensing is available as an option. Speed Sensing monitors the impeller RPM, and should the RPM drop to a certain RPM, the infeed will stop and wait for the RPM of the impeller to come up to full operating RPM, and then it will start feeding in the material. An invaluable tool!
Extra wide 8" infeed opening and 1/2" thick reversible blades!
All welds are continuous for extra strength and durability. 360 degree swivel exhaust chute and exhaust flap is quickly and easily adjusted to direct exhaust.
The Model 824 has four adjustable legs which can be raised for transport through the woods and lowered for storage or operation. The 824 connects easily to any Category 1, 3-point tractor, Minimum horsepower is 15 HP and this unit only requires 540 R.P.M at the P.T.O. The 824 comes with its own hydraulic system and needs no oil from the tractor.
No Ordinary 4" Chipper.
The extra wide infeed hopper allows the bushy branches to be pulled in and chipped. This lessens the amount of pruning that needs to be done. Control handle has a slow speed, fast speed, neutral and reverse to control chip size and feed speed and is easily accessible from either side of the infeed.
Chipper disc is 18-7/8" in diameter and 3/4" thick, with six exhaust paddles, welded and gusseted for strength. There are 2 chip blades, 1/2" thick x 7-1/4" long x 4" wide and they are double sided!
The 824 has only one option, feed sensing. This option counts the impeller R.P.M. and if the tractor is getting loaded up due to a combination of large long logs and not enough horsepower, the Feed Sensing will stop the feed roll and allow the tractor to catch up.
Quality of Workmanship, Innovative Design, Built to Last!
Model 824, 3-Point Hitch Chipper.
Standard Features and Specifications.
PAINT: Orange, polyester powder coat paint provides excellent outdoor weather ability and offer protection against ultra violet discoloration.
HYDRAULIC TANK: 10" x 8-1/4" x 8" steel tank. 2.6 gallon capacity, with lockable filler cap with dip stick.
INFEED CHUTE: 29" wide x 24" high (689 sq. in.) 26-7/8" from edge to roll 28" from ground to tray. ( This is adjustable) Control bar positioned at top of infeed tray to control movement of the feed wheel. High speed, low speed, neutral and reverse.
CHIPPER DISC: 3/4" thick x 18-7/8" diameter disc mounted on a 2" diameter steel shaft with six exhaust blades. Approximately 160 lbs.
CHIPPER BLADES: Two chip blades. Each blade is 7" long x 4-1/2" thick, oil hardened steel. Double sided.
INFEED OPENING: 4" x 8" opening at the infeed roll. Less Trimming and pruning.
BED KNIVES: (2) One horizontal and one vertical. Both are adjustable, reversible and 1" thick steel.
HYDRAULICS: Piston type hydrostatic pump with variable speed control. Maximum feed rate, 94' per minute. Hydraulic hoses - 2,500 lbs. P.S.I. working 10,000 lbs. P. S. I. burst.
FEED ROLL: One 7" diameter x 8" long feed roll, with cutter blades, powered by a variable speed hydraulic pump.
DIMENSIONS: Width 29" Height to top of Discharge 69" Weight 679 lbs. ( approximately)
Payment can be made over the phone via Visa, MasterCard, American Express or Discover by calling 239-357-1853 Craig.